Tools You Need to Install a New Bath Tub
Tools You Need to Install a New Bath Tub
Blog Article
What are your insights and beliefs on Installing A Bathtub?
Mounting a bath tub isn't exactly rocket science, but it does need solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the project can move easily; if you need to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need a helper to vacate the old bathtub and set in the brand-new one. See to it you have actually certified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you mount a brand-new bathtub in your shower room if you have actually already acquired a new bathtub and also don't require to change the plan of your previous water pipes.
Your devices and also material list should make up the following:
Getting ready for the Setup
Firstly, the supporting framework provided with the bath ought to be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted access that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Switch on the water supply and also inspect all joints and new pipework for leakages as well as tighten them if required. Load the bath tub and likewise check the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has been used at the very least once as this will certainly resolve it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, resulting in problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about How to Install a Bathtub? Write a remark down the page. We would be interested to listen to your suggestions about this blog entry. In hopes that you visit us again later on. Liked our blog posting? Please share it. Let somebody else find it. Thanks a bunch for your time. Visit us again soon.
Set Up An Appointment
Report this page